Go to the Web for instructions, No. Yes. Yes. No. Installation Guide. Install the server in the rack, if required. xSeries View and Download IBM Xseries maintenance manual online. Xseries Server pdf manual download. This manual provides information about installing the IBM® Remote Supervisor . v IBM Remote Supervisor Adapter User’s Guide . xSeries Type
Page 45 Table 5. This number is used to cross reference an English caution or danger statement with translated versions of the caution or danger statement in this section. Power-supply Led Errors Note: Viewing Your Configuration Figure 4. System-board manial connectors The following illustration shows the location of the system-board connectors for user-installable options.
System-board switches and jumpers The following illustration shows the location of the switch block SW2 on the system board.
If the diagnostic programs do not detect any hardware errors but the problem persists during normal server operations, a software error might be the cause.
IBM Xseries 345 8670 Maintenance Manual
Switches Switch Switch number Default value description Reserved. Turning on the server You can turn on the server in any of the following ways: Power supply Power cage assembly System board Notes: For information about replacing contaminated thermal grease on the heat sink or fan sink, contact IBM Integrated Technology Mznual. Device configuration error 2. Faites-vous aider pour soulever ce produit.
IBM is not responsible for any radio or television interference causedby using other than recommended cables and connectors or by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. The x354 in this document might differ slightly from your hardware. Installing A Hot-swap Power-supply Installing a hot-swap power-supply Your server supports a maximum of two hot-swap power supplies. These are parameters you assign to outgoing transmit packets.
An enhanced monitor cable with additional shielding is available for the and monitors.
Page 76 For information about replacing contaminated thermal grease on the heat sink or fan sink, contact IBM Integrated Technology Services. Power checkout Power problems can be difficult to solve. Manuao listing xSeries Typ Expansion-slot covers must be installed on all empty slots. When you use an administrator password, you can set, change, or delete both the administrator and power-on passwords and allow a power-on password to be changed by the user.
Page 9 Power-supply LED errors The materials at those Web sites are not part of the materials for this IBM product, and use of those Web sites is at your own risk.
Check system board cable connectors problem. Open the adapter retainer and slide the expansion-slot cover out of the server or PCI riser-card assembly. Not Applicable This result occurs when you specify a diagnostic test for a device that is not present. System board v System board Serial port failed. Electrical current from power, telephone, and communication cables can be hazardous. These programs are the primary method of testing the major components of your server.
Page 10 viii xSeries Type Page 71 MHz front-side bus, the heat-sink retention mechanism surrounding the microprocessor connector is black. For the most up-to-date phone numbers, go to http: To print the manual completely, please, download it.
Beim Anheben der Maschine die vorgeschriebenen Sicherheitsbestimmungen beachten. User Aborted This result occurs when you stop the diagnostic test before it is complete. Page 58 Table 7 describes the function for each switch on the switch block. Rerun the test with a different diskette. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits.
Component Locations Component locations This section manua, illustrations of the system-board and PCI riser-card component locations. Temperature related system shutdown Note: This can simplify network administration when connecting clients to servers that are dispersed geographically across a building, campus, or enterprise network. Component locations This section provides illustrations of the system-board and PCI riser-card component locations.
Hazardous voltage, current, and energy levels are present inside any component that has this label attached. If you need help, service, or technical assistance or just want more information about IBM products, you will find a wide variety of sources available from IBM to assist you. If the problem remains, suspect the following FRUs in the order listed: Page 88 xSeries Type For example, a short circuit can exist anywhere on any of the power distribution buses. Hard disk drive status LED: Page 34 VLANs msnual you the ability to group users and devices together into logical workgroups.