Quick fastener screw 3. Checking the stabilizer bushes The stabilizer bushes must be checked for cracks or damage at the intervals specified in the yamahw maintenance and lubrication chart.
Yamaha GRIZZLY – Manuel du propriétaire – Pages – PDF Manual
Auxiliary DC jack fuse: Page Warranty, extended Refer to this section each time a panel needs to be removed and installed. Improper riding procedures such as abrupt throttle changes, excessive braking, incorrect body move- ments, or too much speed for the sharpness of the turn may cause the ATV to tip.
Replacement of brake components requires professional knowledge. Page 79 Improper riding procedures such as abrupt throttle changes, excessive braking, incorrect body move- ments, or too much speed for the sharpness of the turn may cause the ATV to tip. Place the panel in the original position, and then in- stall the bolts, nut, and quick fastener.
The rear storage compartment is located under the seat. Install the V-belt cooling duct, and then tighten the clamp screw.
EBU Instruments, lights and switches Check that all instruments, lights and switches are working properly. Replacing A Fuse To charge a sealed-type MF battery, a spe- cial constant-voltage battery charger is re- quired. To remove one of the panels 1. Multifunction meter unit 6. Excellent for use in your garage. To decrease If the specified idling speed cannot be obtained as the throttle cable free play, turn the adjusting described above, have a Yamaha dealer make the bolt in direction b.
Always clean up spilled fluid imme- ver should have a free play of zero mm zero in as diately. If this occurs, have a Yamaha ton together for at least three seconds. Page If water has been added to the coolant, have a Yamaha dealer check the antifreeze con- tent of the coolant as soon as possible, oth- 1.
If water has been added to the coolant, have a Yamaha dealer check the antifreeze con- tent of the coolant as soon as possible, oth- 1.
If a protector wears to the point that its indicator be- comes visible, have a Yamaha dealer replace the protector. Select the appropriate drive according to the ter- EWB rain and the conditions. Keep the uine Yamaha accessories. Remove the dipstick, and then wipe it off with a clean rag. However, it is not possible for Yamaha to test all non If you do not have the tools or experience required for a particular job, have a Yamaha dealer perform it for you.
Minimum level mark 1. EBU Rear brake lever Checking and lubricating the front and rear brake levers The operation of the front and rear brake levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
By pressing ‘print’ button you will print only current page. Troubleshooting However, should your ATV re- quire any repair, take it to a Yamaha dealer, whose skilled technicians have the necessary tools, expe- rience, and know-how to service the ATV properly.
Checking The Brake Fluid Level EBU Rear brake Checking the brake fluid level Insufficient brake fluid may allow air to enter the brake system, possibly causing it to become inef- fective.
Loosen the cylinder head air bleed bolt, with- hole, tighten the water pump air bleed bolt to out removing it, to allow all of the air to escape the specified torque. Coolant reservoir hose 6. Engine oil drain bolt Make sure that the O-ring is properly seated.
Page 7 Instruments, lights grlzzly switches The air filter needs more frequent service if you are yamaba in unusually wet or dusty areas. Final gear oil filler bolt 4.
Never exceed the weight limits manuql. If any engine trouble should occur during the engine break-in period, immediately have a 1. All air must be bled from the brake system.
Yamaha dealer adjust Check the operation of the brake levers and pedal. If any leakage is found, have a Yamaha dealer check the cooling system.
Adjust the headlight beam if necessary. Panel I Place the panel in the original position.
Yamaha GRIZZLY 700 FI Owner’s Manual
Coolant temperature warning light: Number of bids and bid amounts may be slightly out of date. After draining the coolant, thoroughly flush the 7. If there is prior to operating the engine for the first time.